Back

To Complete Planter Maintenance Tasks

On March 09, 2019

To Complete Planter Maintenance Tasks

In spite of recent snows, we all know spring is just around the corner. And with the arrival of spring, planting time will quickly follow. Now is the time to work on planter maintenance to prevent breakdowns or poor performance at planting time. Extension Soil Management Specialist Sjoerd Duiker reminds us planter maintenance is essential for optimal no-till results. 

While you may be able to get away with a poorly maintained planter in conventionally tilled soil, not so in tough no-till conditions. A no-till planter must be able to plant through heavy crop residue, penetrate firm soil, open a perfect ‘V’ slot, place singulated seeds at equal distances and at uniform depth, close the seed slot so seeds have proper seed-to-soil contact, not cause side-wall compaction, and not excessively compact soil on top of the seed. Even with good winter maintenance, when you get to the field you should regularly check planter performance and change settings as needed. 

Dysfunctional metering units result in skips, doubles and triples. To guarantee optimal performance, take metering units apart every winter. Remove dirt and clean the hood with soapy water (no kerosene, diesel or oil should ever be used in metering units!). Replace cracked plastic covers. Replace broken fingers in a finger-pickup meter. Use a feeler gauge to check tension on the fingers, then tighten them correctly. Check backplate and seed brushes for wear and replace as needed. The belt (in finger pick-up meters) should be flexible, not have cracks in it, and should be clean. Clean with soapy water and let it dry before putting it back in. When putting the metering unit back together, make sure the rubber belt is placed in the right direction. You can lubricate with graphite (NO OIL or WD-40).  It is recommended to take your finger pick-up metering unit to a dealer to have it calibrated every 100-150 acres or every 3-4 years. Take a bag of your own seed with you and give the correct speed at which you’ll be driving. If you have a vacuum or air meter, check that vacuum or air pressure is correct, check for leaks and wear on knock-off brushes and repair/replace as needed.

Accurate depth placement can be compromised if planter units are loose or wobbly. You should not be able to easily lift a planter unit or move it sideways. Look across your planter units from the side. Are they all at the same height? If one unit is either up or down compared to the others, it needs work. A common problem is that some bolts are loose or additional bushings are needed. You also need to replace cracked or broken seed hoppers. 

Seed opener disks need to have a minimum diameter (check operator manual) or they will not place the seed at the appropriate depth. Seed opener disks also need to come together in the front (they should touch for 3” for old blades but only 1-1.5 inches on newer blades). Stick two business cards between the openers and move them as close together as possible to check this. If opener disks are worn too much you will get a “W” shaped seed slot instead of the desired “V” slot. 

The end of seed tubes may wear to the extent that they curl inwards, catching seeds. There is often a hook halfway up that can easily break off. Seedtube guards need to have their minimum width and be fastened correctly or damage to the seed tube is likely. Clean seed sensors if you have them.

Seed firmers help to press the seed down in the furrow, guaranteeing more accurate depth placement of the seeds. The tension can be adjusted with a bolt. If the seed firmers are worn too much they need to be replaced.

Depth wheels should run tight against disks. Change washers from in- to outside (or vice versa) of depth wheel if necessary. If this doesn’t resolve the problem, the depth wheel arm needs to be replaced.

Check the diameter of the coulters and replace them if needed. You should adjust the depth setting of worn coulters that are still usable.Check the row cleaners for wear. Adjust to compensate for wear or replace if worn too much.

Closing wheels need to have an intact spring and need to be checked for damage or wear as well. Bearings cannot be wobbly or too tight. The bottoms of rubber or cast-iron closing wheels need to be 1.5”-2” apart. The closing wheel arm cannot have too much play. If so, bushings or the entire arm may need replaced.

An important step is to check the alignment of coulters, opener disks, and closing wheels. Take a rope and pull it straight from the front coulter to the closing wheels. The firming wheels, seed openers, and coulters should all be in line. Closing wheels should not run on top of the seed furrow.

The insecticide boxes should have no holes or cracks. Tubes should be blown out with air as well as the slot on the bottom of the meter. Fertilizer opener disks should have a minimum diameter (check manual). The bearings should not be wobbly or too tight. Hang a bucket below the tube of the unit, and do a test run of 175 feet in the field. Weigh the fertilizer in the bucket, multiply by 100, and you have the fertilizer you’ll put on in pounds per acre (at 30” row spacing). Adjust as needed. Check all chains and their sprockets. If they are worn or chain links are stiff they need to be replaced. Chains need to have the appropriate tension and should be lubricated properly. A final step in proper planter maintenance is to inflate tires to the correct pressure. With this task completed you will be ready to go when planting time arrives.

Quote Of The Week: “Your children are heirs to your lifestyle, your daily witness to your values.” Suzanne Woods Fisher-Amish Proverbs